There are actually three kinds of drywall panels (determined by thickness).
one. one/2 to sixteen inches or a lot less - For framing
This sort of drywall is properly used for partitions. But if you are plastering an aged wall the correct thickness that you need to use would be the three/eight inches.
two. 5/eight to 24 inches - For ceilings
The ceiling panels must constantly be thicker compared to the drywall panels used in your wall.
3. 1/two inch water-proof - for humid spots like bathrooms (although mold resistant drywall panels are Employed in basements).
In spots wherever You will find a direct and oblique contact with drinking water, you must utilize a water-resistant panel. Also continue to keep this in mind Using the spots in which molds are current; you need to utilize the mildew resistant drywall panel.
Drywall panels are available in different measurements and dimensions. Some are 4x8 or 4x12 and In case you are closer to major manufacturer, you can find even larger sheets for ceiling like 14ft-54ft lengths and 9ft widths. The 4x8 panels weigh 55 lbs while the 4x12 panels weighs eighty two lbs.
Equipment to get ready
• four-ft. T-square
• Drywall screw gun
• Keyhole drywall saw
• Surform Software
• Flat bar
• Utility knife
• Chalk line
• Trim hammer (sixteen or twenty oz.)
• Drywall observed
• Drywall hammer
• Foot raise
• Drywall elevate
• Spiral cutout saw
• Putty knife
• Flusher
• Applicator
Installation Ways
1. Be sure that There's suitable wood backing during the areas exactly where drywall panels do not have aid. Look at every single corner and ceiling or wall joints.
two. Measure the best length on the needed panels using the T-sq.. From The full panel, Slash the desired length using a utility knife and Slice the panel with the bottom. Make sure the sides are correctly Reduce and easy using a surform Software. Gaps between panels must be under one/four inches.
Notice: 4x8 panels can go over 32 sq.ft though the 4x12 panel can include forty eight sq.ft. Purchase adequate of drywall panels to accomplish the whole challenge If you're able to. It is really okay In case you are brief some panels, it is healthier to make A fast operate to add handful of more panels than inventory extra panels you can expect to never use.
3. Initial put in the drywall panels within your ceiling right before continuing towards the partitions. You need an assistant to connect the drywall panels to the partitions and ceiling. Make use of a carry to set up twelve ft or bigger panels towards your ceiling. Keep the panel to the proper placement and pre-nail the panels. Once the panels are in place, fasten the panels using the drywall screws. Do this method to your complete ceiling.
Attaching panels during the ceiling is simpler as they can be a flat area they usually haven't got numerous holes to eliminate (aside from a couple of mild bulb patterns) as opposed to the walls wherever you might want to eliminate designs to the Home windows, doorways, electrical stores and Other folks.
In slicing patterns for gentle bulbs within the ceiling, shops, doors, windows and small openings You can utilize the spiral Slice-out saw.
four. When you are finished With all the ceiling, begin slicing the panels for partitions, Home windows and doors utilizing the drywall noticed or keyhole saw for small cuts. Make use of the T-square for straight pattern and Minimize the drywall panel using the utility knife. Keyhole saws are also used to Reduce the patterns for electrical shops and also other little cuts.
5. In installing drywall panels to your wall, make sure to thrust the panel tightly in the direction of the edge in the ceiling right before fastening it. Steer clear of breaking joints at the window and doorway edges given that they will turn out cracking which can be a dilemma when You begin taping.
six. Use drywall screws to fasten the panels on your partitions. More time nails and screws will not be advisable simply because they tend to be more prone to popping. Nails are only for assist or secondary hold, Therefore the screws are the key fasteners. Which is why Placing the drywall screws set up is the final phase you'll want to do right after Placing many of the drywall panels of their positions.
7. Check out the protruding screws and nails utilizing hanging drywall a putty knife above Each individual screw and nail head. In case you hear a click on, then your nail or screw needs to be pushed in even further - but usually do not overdo it as it will eventually damage the drywall panel.
Following the lengthy system of putting in the drywall panels, the subsequent step you must do is taping. The main reason why you might want to appropriately tack the nails is that they will present and turn into a enormous distraction when you start taping.
For a quick position in taping, particularly in the corners, you can be employing drywall flusher. It really is preferable to use drywall flusher from the corners mainly because they have sleek flat blades to evenly distribute the mud to the corners. An applicator Then again, Despite the fact that they are often Employed in corners, should be used for even mud distribution in flat surfaces, edges and curved places.